An oil is rated 10W-30. What does the 10W part of the rating mean?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 8-7, Multiweight Oils. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
An oil that is too thin is used in hot weather. What is the result?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 8-6, Viscosity and Viscosity Measurements. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
How is the water pump driven on most engines, by TM 9-8000?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 9-7, Water Pump. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
The oil pressure warning light comes on while the engine is running. Why should the engine be shut down at once?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 17-4, Pressure Gages (indicator lamp). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
Show all 68 questions (64 more)
Engine systems, continued
Spark plugs of too hot a heat range are fitted. What happens to them?US Army TM 9-8000, Principles of Automotive Vehicles (1985), chapter 15, Spark plugs (heat range). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
Technician A says engine oil is changed because the oil itself wears out. Technician B says oil is changed because it becomes contaminated. Who is right?US Army TM 9-8000, Principles of Automotive Vehicles (1985), chapter 8, Oil contamination. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
Thick sludge is found inside a crankcase. By TM 9-8000, what forms it?US Army TM 9-8000, Principles of Automotive Vehicles (1985), chapter 8, Oil contamination. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
What do the additives in a detergent oil do?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 8-8, Detergent Oils. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
What does the resistor built into a resistor spark plug do?US Army TM 9-8000, Principles of Automotive Vehicles (1985), chapter 15, Spark plugs (resistor spark plugs). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
What is the fan shroud for?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 9-8, Fan and Shrouding. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
Why is a leaking exhaust system dangerous even when no fumes can be smelled?US Army TM 9-8000, Principles of Automotive Vehicles (1985), chapter 7, Exhaust emissions (carbon monoxide). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area A, Engine Systems.
Automatic transmission and transaxle 5
An automatic transmission has just been refilled. Before the level is rechecked, what is done with the engine idling and the brakes applied?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 7, Refilling the transmission. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area B, Automatic Transmission/Transaxle.
Technician A says a disposable transmission filter should always be replaced once it has been removed. Technician B says a cleanable screen should be wiped dry with a shop rag. Who is right?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 7, Fluid replacement. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area B, Automatic Transmission/Transaxle.
The transmission pan is removed for a fluid service and a large number of metal particles lie in the bottom. What does this suggest?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 7, Fluid replacement. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area B, Automatic Transmission/Transaxle.
What does the Navy manual say comes of adding the wrong type of fluid to an automatic transmission?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 7, Checking the fluid. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area B, Automatic Transmission/Transaxle.
Which kind of use puts a vehicle on the severe service schedule for transmission fluid and filter changes?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 7, Fluid replacement. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area B, Automatic Transmission/Transaxle.
Manual drive train and axles 7
A propeller shaft has a universal joint at each end. How must the two yokes on the shaft itself be set?US Army TM 9-8000, Principles of Automotive Vehicles (1985), chapter 28, Conventional universal joints. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area C, Manual Drive Train and Axles.
A steady humming noise comes from the differential on a straight road. What does it generally mean?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 11, Troubleshooting the differential. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area C, Manual Drive Train and Axles.
The boot over a universal and slip joint is torn. Why does the joint then wear quickly?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 11, Service and maintenance. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area C, Manual Drive Train and Axles.
By the Navy manual, what is best replaced or done together when a worn clutch is renewed?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 7, Clutch malfunctions (dragging). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area C, Manual Drive Train and Axles.
In a hydraulic clutch operating system, what moves the clutch release arm?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 7, Clutch systems (hydraulic operating system). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area C, Manual Drive Train and Axles.
What is the slip joint at one end of a propeller shaft for?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 11, Propeller shaft assemblies. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area C, Manual Drive Train and Axles.
Where should the lubricant level usually be in a manual gear case or axle housing?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 11, Service and maintenance. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area C, Manual Drive Train and Axles.
Suspension and steering 16
A combined low tire pressure and TPMS malfunction telltale flashes for about a minute after start-up, then stays lit. What does that sequence signal under FMVSS 138?49 CFR 571.138 (FMVSS 138, Tire pressure monitoring systems), S4.4, TPMS malfunction. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
A tire is worn at both edges of the tread, with the center still good. Which cause does the Navy manual give?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 12, Steering and alignment trouble (tire wear). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
The coil spring sits on the lower control arm, so the lower ball joint carries the load. Where is the jack placed to check that ball joint for play?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 12, Alignment procedures. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
How far may toe-in or toe-out depart from the setting in the maker's service specification under 49 CFR 570.7?49 CFR Part 570 (Vehicle in Use Inspection Standards), section 570.7(d), Alignment. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
How is the center of steering gear travel found before toe is set, by the Navy manual?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 12, Toe-in and steering wheel adjustment. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
How much total indicated runout may a rim bead area have under 49 CFR 570.10?49 CFR Part 570 (Vehicle in Use Inspection Standards), section 570.10(b), Deformation. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
In what order does the Navy manual suggest the alignment adjustments be made?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 12, Adjustable suspension angles. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
In what respects must the two tires on one axle be matched under 49 CFR 570.9?49 CFR Part 570 (Vehicle in Use Inspection Standards), section 570.9(b), Type. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
The last four digits of a tire identification number are 3524. When was the tire made?49 CFR 574.5 (Tire identification requirements), section 574.5, Tire identification requirements (date code). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
One front tire is worn on one side of the tread only. Which alignment fault does the Navy manual give for that pattern?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 12, Steering and alignment trouble (tire wear). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
Technician A says a cut ball joint seal fails the suspension standard of 49 CFR 570.8. Technician B says a spring spacer fitted to one front spring only is acceptable under it. Who is right?49 CFR Part 570 (Vehicle in Use Inspection Standards), section 570.8(a), Suspension condition. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
Under 49 CFR 570.9, when do the tread depth indicators of a passenger car tire become exposed?49 CFR Part 570 (Vehicle in Use Inspection Standards), section 570.9(a), Tread depth. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
What is the effect of negative caster on steering?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 12, Steering geometry (caster angle). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
Where does FMVSS 110 put the placard that gives the maker's recommended cold tire inflation pressures?49 CFR 571.110 (FMVSS 110, Tire selection and rims and load carrying capacity information), S4.3, Placard. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
Which power steering condition fails the inspection standard of 49 CFR 570.7?49 CFR Part 570 (Vehicle in Use Inspection Standards), section 570.7(e), Power steering system. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
Which shock absorber finding fails 49 CFR 570.8?49 CFR Part 570 (Vehicle in Use Inspection Standards), section 570.8(b), Shock absorber condition. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area D, Suspension and Steering.
Brakes 14
A brake fluid container is empty. What does the caution required on its label by FMVSS 116 say about the container?49 CFR 571.116 (FMVSS 116, Motor vehicle brake fluids), S5.2.2.2, Packaging and labeling. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
A noise seems to come from the brakes. What does the Navy manual do before the brakes are blamed?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Brake noise. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
A truck with hydro-boost brakes has both a high brake pedal effort and heavy steering. Technician A says a loose or broken power steering belt could be the cause. Technician B says a low power steering pump fluid level could be the cause. Who is right?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Hydroboost troubleshooting. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
A vacuum booster is tested: the pedal is pumped with the engine off, then held down while the engine is started. What shows that the booster works?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Troubleshooting vacuum-assisted hydraulic brakes. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
After a drum brake job by a new mechanic, one wheel brakes poorly. Which assembly mistake does the Navy manual warn about?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Inspecting and troubleshooting hydraulic brake systems. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
The antilock system misbehaves on a car whose alternator has failed. What does the Navy manual say about this?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Antilock brakes. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
The brakes take too much pedal effort on a car with no power booster. Technician A says glazed brake linings could be the cause. Technician B says binding pedal linkage could be the cause. Who is right?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Brakes too hard to apply. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
How does the Navy manual test a hydraulic brake system for leakage?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Inspecting and troubleshooting hydraulic brake systems. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
One rear wheel drags with the brake pedal released, and the other wheels turn freely. Which cause does the Navy manual list?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Brakes drag. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
The parking brake of a car with an automatic transmission is tested on level ground with the brake set. What result shows it is holding?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Parking/emergency brakes. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
What color must DOT 3 and DOT 4 brake fluid be under FMVSS 116?49 CFR 571.116 (FMVSS 116, Motor vehicle brake fluids), S5.1.14, Fluid color. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
What does the warning required on a brake fluid reservoir by FMVSS 135 tell the technician to do before the cap comes off?49 CFR 571.135 (FMVSS 135, Light vehicle brake systems), S5.4.3, Reservoir labeling. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
What is the most common cause of a soft or spongy brake pedal?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Soft pedal. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
Why must wheel lug nuts be tightened to the correct torque and in the proper sequence on a vehicle with antilock brakes?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 6, Antilock brakes. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area E, Brakes.
Electrical 10
A corroded connection adds resistance between the alternator output terminal and the battery. What is the result?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 4, Charging system circuit resistance test. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area F, Electrical.
A double-filament stop and tail lamp bulb has two contacts on its base. How do the two filaments return to ground?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 16-2, Lamps (construction). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area F, Electrical.
A starter current draw test reads higher than normal. Technician A says that with a normal cranking load this points to trouble in the starting circuit. Technician B says higher current is normal on a newly overhauled engine. Who is right?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 4, Cranking voltage test. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area F, Electrical.
All the headlights go out at the same time. What does the Navy manual check first?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 4, Headlights. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area F, Electrical.
How is a battery charger connected to a battery?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 12-5, Charge (electrical action). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area F, Electrical.
How is a brake light switch that has power tested with a test lamp?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 4, Brake lights. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area F, Electrical.
One filament of a sealed-beam headlamp burns out. What is replaced?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 16-4, Headlights (sealed beam). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area F, Electrical.
The starter draws low current and the engine cranks slowly or not at all. What does the Navy manual say to look for?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 4, Starting motor current draw test. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area F, Electrical.
The turn signal lamps come on but do not flash. Which part is usually at fault?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 4, Directional signals. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area F, Electrical.
When should a no-charge indicator lamp be lit on a sound charging system?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 17-2, Battery Condition Gages (indicator lamp). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area F, Electrical.
Heating and air conditioning 5
An air conditioner cools poorly and the condenser fins are packed with bugs and leaves. What does the Navy manual do about it?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 13, Malfunctions of components (condenser). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area G, Heating, Ventilation, and Air Conditioning.
Bubbles or foam show in the sight glass while the system runs on a warm day. What may that indicate?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 37-4, Receiver (sight glass). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area G, Heating, Ventilation, and Air Conditioning.
Clear water drips under a car while the air conditioner runs. Where does it come from?US Army TM 9-8000, Principles of Automotive Vehicles (1985), paragraph 37-6, Evaporator. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area G, Heating, Ventilation, and Air Conditioning.
Who may buy a container holding less than 20 pounds of a class I or class II refrigerant suitable for vehicle air conditioners, under 40 CFR 82.34?40 CFR Part 82, Subpart B (Servicing of Motor Vehicle Air Conditioners), section 82.34(b), Prohibitions and required practices. Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area G, Heating, Ventilation, and Air Conditioning.
Why were the threaded service fittings of R-134a systems made different from those of R-12 systems?US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992), chapter 13, Functional testing (new refrigerant). Outline: ASE Auto Maintenance and Light Repair Study Guide (copyright 2026), Test G1, content area G, Heating, Ventilation, and Air Conditioning.
How this list was compiled: Our own questions, written to the seven content areas of the Auto Maintenance and Light Repair (Test G1) test specifications and task list in the ASE Auto Maintenance and Light Repair Study Guide (copyright 2026, https://ase.com/wp-content/uploads/ASE_MaintenanceLtRepair_Study_Guide.pdf, linked from https://ase.com/tests/g1/, both opened 2026-10-08), in its shares of 9, 4, 6, 13, 11, 8 and 4 of 55 questions. The bank holds 11, 5, 7, 16, 14, 10 and 5 in that order. Every fact was read on 2026-10-08 in the public text the question names: 49 CFR Part 570 (vehicle in use inspection standards), 49 CFR 571.110, 571.116, 571.135 and 571.138, 49 CFR 574.5 and 40 CFR 82.34 at ecfr.gov; US Army TM 9-8000, Principles of Automotive Vehicles (1985); and US Navy NAVEDTRA 14050, Construction Mechanic, Advanced (1992). The sample questions printed in the study guide were not used. Licence: Questions, choices and explanations are original work of this site.
How it works
This free ASE G1 test practice has 68 maintenance and light repair questions of our own, weighted like the real test. It is unofficial and not affiliated with, endorsed by or sponsored by the National Institute for Automotive Service Excellence (ASE).
Read the full guide
What the G1 test covers
ASE's study guide lists seven areas: engine systems 9, automatic transmission 4, manual drive train and axles 6, suspension and steering 13, brakes 11, electrical 8, heating and air conditioning 4. This ASE maintenance and light repair practice test keeps those shares: 11, 5, 7, 16, 14, 10 and 5.
An ASE MLR practice test with sources
Inspection limits come from federal inspection standards and the tire, brake fluid and refrigerant rules. Service steps come from Army and Navy manuals, which do not cover scan tools or oil life monitors.
Timed or on paper
Exam mode asks 55 questions in 90 minutes. The official ASE G1 study guide PDF is free and holds the task list; this bank prints as a paper test to go with it.
Suspension, steering and brakes are 24 of the 55 questions. Start with tires, alignment angles and brake fluid.
Questions and answers
How many questions are on the ASE G1 test?
ASE's page for G1 lists 55 scored questions plus 10 unscored research questions, in 90 minutes. You are not told which are which, so answer every one. The recertification test is 28 questions in 45 minutes.
Can I take the ASE G1 test online?
Yes, in one way. By ASE's 2026 guide to certification, a first-time G1 test may be taken at a test center or with live remote proctoring. This practice page is free and online, and it is not the real test.
Are these real ASE G1 test questions?
No. The real questions are not public. Every question here is our own, written from the task list in the ASE G1 study guide, which ASE gives away free, and from public sources. None copies its sample questions.
What is the G1 ASE test for?
ASE's page says it recognizes technicians who can perform the most common maintenance and light repair tasks. The study guide adds that students who pass eight entry-level tests in an accredited program can earn G1 without sitting it.